sgi onyx350

onyx350が届いた。
送料元払いだったのに、相手がミスって着払いになっていた。
朝5時に佐川に身請け。
筐体の状態はそこそこ、予想していたように、Expansion moduleだった。
よってHDやDVD-ROMなどは一切なし。
HDキャリアにはブランクパーツが入っていた。
おまけに凄いほこりがたまっていた。
基本的にHDなどはExpansion moduleにはオプション扱いのようだ。
pciにはファイバーチャネル、ADAT入力が付いたオーディオカード、SCSIカード。
InfinitePerformanceが入るところにはDmedia proが入っていた。
早速電源を入れると、シュルシュルという轟音がFANから出ていきなりFANエラー。
終わってる....
んで、絵がでないから、シリアルコンソールに繋いでパワーオンと景気よく行きたいが、
kermitの設定で四苦八苦。
set line /dev/tty0p0
set speed 38400
set parity none
set serial 8N1
set flow RTS/CTS
set carrier-watch off
でok。

returning to console mode  001c24 CPU0, <CTRL_T> to escape to L1
ctr+tを入力
escaping to L1 system controller
001c24-L1>
001c24-L1>power up

returning to console mode  001c24 CPU0, <CTRL_T> to escape to L1
Starting PROM Boot process  
io_config_space: No IOC3 or IOC4 found on BASEIO.
io_config_space: Found 0 Qlogic devices BASEIO; expected 1 or more.
io_config_space failed:  
RSLT io_config_spac FAIL                diag_rc = 53                            
diag_io6confSpace_sanity: /hw/module/001c24/xtalk/15: FAILED


IP35 PROM SGI Version 6.210  built 02:33:51 PM Aug 26, 2004
Testing/Initializing memory ...............             DONE
Copying PROM code to memory ...............             DONE
Discovering local IO ......................             DONE
Discovering NUMAlink connectivity .........
Local hub NUMAlink is down.
*** Local network link down
DONE
Found 1 objects (1 hubs, 0 routers) in 5897 usec
Waiting for peers to complete discovery....             DONE
No other nodes present; becoming global master
Global master is /hw/rack/001/bay/24
Intializing any CPUless nodes..............             DONE
Checking partitioning information .........             DONE
No other nodes present; becoming partition master
Local slave entering slave loop
Loading BASEIO prom .......................             Local slave entering slave loop
Local slave entering slave loop
DONE

BASEIO PROM Monitor SGI Version 6.210  built 02:30:38 PM Aug 26, 2004 (BE64)
4 CPUs on 1 nodes found.
****************************************************************

*1222560370*       WARNING:  No BASEIO board found -- the system         *

*1222560371*                  will not be able to boot.                  *
****************************************************************
WARNING: Did not find an IOC3 or IOC4 NVRAM base address
WARNING: Did not find an IOC3 or IOC4 UART base address

NVRAM checksum is incorrect: reinitializing.
Automatic update of PROM environment disabled
Graphics diagnostics

WARNING: Did not find an IOC3 or IOC4 NVRAM base address
WARNING: Did not find an IOC3 or IOC4 UART base address
Installing PROM Device drivers ............             
Initializing PROM Device drivers ..........             DONE
cpu_get_tod: Did not find an IOC3 or IOC4 NVRAM base address
Checking hardware inventory ...............              
WARNING: hardware inventory is invalid.  Reinitializing...
Writing 4 records.... DONE
Updated new configuration. Wrote 4 records.

**** System Configuration and Diagnostics Summary ****
CONFIG:
         No. of NODEs enabled    = 1
         No. of NODEs disabled   = 0
         No. of CPUs enabled     = 4
         No. of CPUs disabled    = 0
         Mem enabled             = 2048 MB
         Mem disabled            = 0 MB
         No. of RTRs enabled     = 0
         No. of RTRs disabled    = 0

DIAG RESULTS:
         ALL DIAGS PASSED.
**** End System Configuration and Diagnostics Summary ****


System Maintenance Menu

1) Start System
2) Install System Software
3) Run Diagnostics
4) Recover System
5) Enter Command Monitor

Option? 
5を入力
>> hinv -v
IP35 Node Board, Module 001c24
    ASIC BEDROCK Rev 2, 200 MHz, (nasid 0)
    Processor A: 700 MHz R16000 Rev 2.1
          Secondary Cache 4MB 350MHz Tap 0xc , (cpu 0)
      R16010FPC Rev 2.1
    Processor B: 700 MHz R16000 Rev 2.1
          Secondary Cache 4MB 350MHz Tap 0xc , (cpu 1)
      R16010FPC Rev 2.1
    Processor C: 700 MHz R16000 Rev 2.1
          Secondary Cache 4MB 350MHz Tap 0xc , (cpu 2)
      R16010FPC Rev 2.1
    Processor D: 700 MHz R16000 Rev 2.1
          Secondary Cache 4MB 350MHz Tap 0xc , (cpu 3)
      R16010FPC Rev 2.1
    Memory on board, 2048 MBytes (Standard)
      Bank 0, 512 MBytes (Standard)  <-- (Software Bank 0) 
      Bank 1, 512 MBytes (Standard) 
      Bank 2, 512 MBytes (Standard) 
      Bank 3, 512 MBytes (Standard) 
XT-DIGVID Bridge, Module 001c24
IXBRICK Bridge, Module 001c24
    ASIC BRIDGE Rev 3, (widget 15)
    adapter ID (Vendor 1077 Device 1240 class 1 subclass 1)
          (pci id 1)
    adapter RAD 
          (pci id 2)
IXBRICK Bridge, Module 001c24
    ASIC BRIDGE Rev 3, (widget 15)
    adapter ID (Vendor 1077 Device 2312 class c subclass c)
          (pci id 2 function 0)
    adapter ID (Vendor 1077 Device 2312 class c subclass c)
          (pci id 2 function 1)
ASIC XBOW Rev 3, on CBrick, Module 001c24
ctr+dをおして
001c24 ATTN: FAN 0 warning limit reached @ 0 RPM

とりあえず、FANの問題は室温が高すぎるかららしい...
この寒いなかクーラーきかせろってか?
cpuが700mhzでメモリが2GBなのはうれしい誤算。
とりあえず室温を下げて実験続行か...